S/V Constance, Alberg 30 #262 -- 2017 Recommissioning for Launch on on 2017-04-19

MUST DO

CLOSE ALL THRUHULLS BEFORE SPLASHING THE BOAT -- Engine (2), Galley (1), Head (2), Bilge Pumps (2), Cockpit Scuppers (2)

OPEN COCKPIT SCUPPERS AFTER LAUNCH

CHECK STUFFING BOX AFTER LAUNCH

CHECK KNOTMETER BLANKING PLUG AFTER LAUNCH

• General
  • Remove Cover -- Done 2017-04-16
  • Attach dock lines -- Done 2017-04-19
• Electrical
  • Charge batteries -- Done 2017-04-09
• Engine
  • Engine Raw Water System
    • Install raw water strainer -- Done 2017-04-09
    • Connect raw water strainer to raw water cooling pump -- Done 2017-04-09
    • Install raw water thru hull strainer on outside of hull
    • Install impeller into raw water cooling pump -- Done 2017-04-04
    • Install raw water cooling pump Done 2017-04-04
    • Connect outlet of raw water cooling pump to heat exchanger -- Done 2017-04-09
    • Install raw water pump fan belt -- Done 2017-04-09
    • Verify connections of exhaust cooling water hose to and from siphon break -- Done 2017-04-16
  • Install alternator fan belt -- Done 2017-04-04
  • Remove rag from engine air intake -- Done 2017-04-09
  • Reorient engine air intake to face downward -- Done 2017-04-09
  • Check engine oil level -- Done 2017-04-09
  • Check tranny oil level -- Done 2017-04-19
  • Check for water in the diesel tank -- Done 2017-04-09
  • Check engine cooling fluid level -- Done 2017-04-09
  • Start engine and verify water flow -- Done 2017-04-09
  • Stow replacement air filter, primary and second diesel filters, and spare fan belts aboard -- Done 2017-04-09
• Hull
  • Affix 2017 DNR registration stickers, and boat registration number on bow, starboard and port -- Done 2017-04-05
  • Paint bare spots on hull below waterline -- Done 2017-04-16
  • Test electric bilge pump -- Done 2017-04-09
• Rigging
  • Re-install chainplates -- Done 2017-04-04
  • Re-attach shrounds to chainplates using pins in the flashlight Snapware container -- Done 2017-04-04
  • Tighten four bolts holding mast to mast step -- Done 2017-04-16
  • Snug up shrouds. Will be tuned after the boat sits in the water for a few days and relaxes into her natural shape -- Done 2017-04-04
• Sails
  • Stow winch handles -- Done 2017-04-16
  • Stow jib, jib sheets, jib sheaves. Sheaves are in Snapware box with other rigging items -- Done 2017-04-05
  • Stow mainsail -- Done 2017-04-05
  • Stow spinnaker
• Gear
  • Stow lifejackets -- Done 2017-04-04
  • Stow tools

• Check all thru hulls -- Done 2017-04-19
• Check stuffing box -- Done 2017-04-19
• Open cockpit scupper valves -- Done 2017-04-19
• Change diesel fuel filter (Racor 110A)
• Change diesel fuel filter on engine
• Change engine air filter
• Change anti-freeze
• Check fan belts
• Re-tension rigging
• Align propeller shaft

MAY DO

• Electrical
  • Relocate battery Newmar ABC123 15 amp battery charger
• Galley
  • Install galley sink
  • Install drain fixture in galley sink
  • Install tail piece on galley sink outlet
  • Install tail piece on galley sink valve
  • Install hose connecting the two tail pieces
• Hull
  • Discard No-Damp in v-berth
  • Stow and secure table below foredeck
• Rigging
  • Lubricate jib furling line sheaves
  • Re-reeve jib furling line -- Done 2017-04-16
  • Install reefing line